Tuesday 03 / December / 2024
For many years, Dubai, which implemented a policy of having 25% of all new buildings 3D printed within 2030, has held the
pole position for 3D construction printing, but that position is now challenged by Oman - printing the world’s largest 3D
printed real concrete building in Oman with a super low cost of the printed materials.
The German University of Technology in Oman, GUtech on Tuesday, December 14, 2021, celebrated the finishing of the 3D
printing of the walls of the so far largest 3D printed building in the world made with a real concrete. The importance of the
event was marked by the presence of His Excellency Sultan Al-Habsi, Minister of Finance of Oman together with more than
200 guests including several ministers and VIPs of Oman, who attended the event in Muscat, the capital of Oman.
The house consists of 190 m2 (2,100 SF) and is typical for a social housing unit in Oman. It has 3 bedrooms, three bathrooms,
a living room, kitchen, and guest reception area. The house was printed in two stages. While the materials recipe was
adjusted and training of the Omani crew took place during the printing of the first part of the house, the second part of the
house was done by the Omani crew on their own and it only took five days to complete. A sign of fast learning and
productivity improvements occurring in 3D printed projects.
Dr. Hussain, Acting Rector of GUtech said “Today’s display of the first 3D printed building is perhaps the first step in the 1,000-
mile journey. A step that will not be success without the support of all parties involved. In this regard, I sincerely thank all the
local and international parties who contribute to supporting the center and the University. We hope that this center will play its
part in supporting Oman's efforts to achieve Oman's Vision 2040.”
While the Middle East have seen numerous 3D printed buildings, the 190 m2 (2,100 SF) building in Oman is the first to be
printed with a real concrete instead of the traditional dry mix mortars used in most other 3D printed buildings. To make the
concrete 3D printable, GUtech applied the D.fab solution developed by COBOD and CEMEX in cooperation where the
concrete can have particle sizes up to 10 mm (1/3 inch) and is made from locally available cement, sand, and gravel. CEMEX
and COBOD launched the news about the D.fab solution last week in connection with the first 3D printed building in Angola.
The D.fab solution was also used in Angola with the result that the cost of the concrete materials was less than 1,000 USD for
the 52 m2 (575 SF) house.
On that occasion Juan Romero, Executive Vice President Sustainability, Commercial, and Operations Development of CEMEX
said: “The introduction of this revolutionary 3D printing system is a testament to our customer-centric mindset and relentless
focus on continuous innovation and improvement. Working together with COBOD, we have developed an experience for
customers that is superior to anything that has been provided in the past”.
In the case of Oman, more than 99.5% of the materials used were local, with less than 0.5% coming from Europe in the form
of the D.fab additives. In Oman the cost of materials for 3D printing of the walls of the 190 m2 (2.100 SF) house was less than
1,600 Euro. According to COBOD, if a printable dry mix mortar had been used the cost of the materials would be more than
20,000 Euro, and it was such significant cost reductions which COBOD and CEMEX was aiming for with their cooperation.
Commenting on this milestone for the widespread adoption of the 3D construction printing method, Henrik Lund-Nielsen,
Founder & General Manager of COBOD International stated: “While we have been happy to help various cement and concrete
manufacturers develop dry mix 3D printable mortars, we have also insisted on that a solution for making real concrete made
from local available materials would be needed for mass application of our technology. We are more than pleased that
CEMEX took on the challenge, and proud that we in cooperation could develop the new solution, which GUtech has now
applied to the first building in Oman. With the low cost for the printed materials, on top of the savings from not needing
formwork and the minimal crew needed to operate our printers, our disruptive technology is now more competitive than ever
before in Oman and everywhere in the world”.
